Lutz homeowners, the cold front is on the way, and the first chilly morning is when we get the same question over and over: “My thermostat says Aux Heat. Is something wrong?” Most of the homes we service in Lutz, from the older ranch houses near US-41 to the newer neighborhoods off Sunlake and Lutz Lake Fern Road, heat with an electric heat pump and backup heat strips. Those systems work great in Tampa Bay, but the thermostat settings confuse a lot of people. Here’s what the screen is telling you and what to check now, before you actually need the heat.
Our licensed techs at Nolan Air run heating calls across north Hillsborough every week. If you’d rather skip the homework, start with our Lutz HVAC service page.
How your heat pump actually heats
A heat pump is your AC running in reverse. In heat mode it pulls warmth out of the outdoor air and moves it inside. On a mild Florida winter day that’s very efficient. When it gets colder, or when you ask the house to warm up fast, the system brings on electric heat strips inside the air handler to help. Those strips work like a big toaster: quick heat, but they use a lot more electricity than the heat pump itself.
Aux Heat: usually normal
When your thermostat shows Aux Heat or Auxiliary Heat, the heat strips are helping the heat pump. That’s normal on a cold morning, after you bump the temperature up several degrees, or while the outdoor unit runs a defrost cycle. You might see a little steam rise off the outdoor unit during defrost. That’s normal too.
What isn’t normal: Aux Heat running nonstop when it’s in the 50s or 60s outside, a power bill that jumps way out of line with the weather, or Aux Heat on while the outdoor unit sits silent. Those point to a heat pump that isn’t pulling its weight, often a failed capacitor, low refrigerant, a stuck reversing valve, or a defrost problem.
Emergency Heat: only for emergencies
Emergency Heat (EM Heat on many thermostats) is a setting you choose. It shuts off the outdoor heat pump and runs the house on heat strips alone. It’s meant for when the outdoor unit is broken or iced over and you need heat until a tech gets there. Leaving it on by accident is one of the most common reasons for a shocking winter electric bill. If your thermostat has an EM Heat light on and you didn’t mean to set it, switch it back to regular Heat.
Thermostat habits that save you trouble
- Make small changes. Jumping the setpoint five or six degrees at once almost always calls in the heat strips. Two degrees at a time keeps the heat pump doing most of the work.
- Go easy on big overnight setbacks. With a heat pump, a large setback means the strips come on in the morning to catch up. A modest setback, or none, often costs less.
- Check the system type in smart thermostats. If a smart thermostat was installed as “conventional” instead of “heat pump,” it can run the strips at the wrong times or never switch to heat mode correctly. If your heat has acted strange since a thermostat swap, that’s worth a look.
Run a test now, while it’s still mild
Set the thermostat to Heat and raise it two or three degrees above room temperature. Within a few minutes you should feel clearly warm air at the vents, and the outdoor unit should be running. Let it go about fifteen minutes. A light burning-dust smell for the first few minutes is normal as the strips burn off months of dust. If that smell lasts more than an hour, smells like hot plastic or wiring, or you see smoke, shut the system off and call us.
Lutz-specific things we see
Lutz has a lot of lakes, tall pines, and big oaks, and outdoor units here pick up needles, leaves, and pollen fast. A clogged outdoor coil hurts a heat pump in winter just like in summer, because that coil is where it collects heat. Rinse it gently with a hose and keep about two feet clear around the unit. Homes on larger lots also get more mice and rats moving into attics and air handlers once nights cool off, and chewed wiring is a real cause of no-heat calls. Garage air handlers, common in older Lutz homes, are worth a quick look for rust, standing water, or a filter that hasn’t been changed since spring.
What our heating tune-up covers
A pre-winter heat pump check from Nolan Air covers the reversing valve, defrost controls, refrigerant charge, heat strips and their sequencers and limit switches, capacitor, contactor, blower, condensate drain, electrical connections, and the thermostat setup, including the system type and Aux Heat settings. See our Lutz heating page for more, or if your test already failed, our Lutz heat pump repair techs can track it down.
Neighbors are getting ahead of it too
We’re booking heating checks across the area this week, including in Northdale, Pebble Creek, and Keystone. Once the first cold night hits, everyone turns the heat on at once, so it pays to get on the schedule while the weather is still mild.
Get your Lutz heater checked now
Don’t wait for a cold morning and a blinking Aux Heat light to find out something’s off. Call Nolan Air at (727) 353-9293 or schedule online. Our office is open Monday through Friday, 8am to 7pm, and you can always find us at NolanAir.com.