Riverview runs on heat pumps. Drive through Panther Trace, Summerfield, Rivercrest, or any of the newer neighborhoods off Big Bend Road and Boyette, and almost every house has a heat pump out back doing double duty: cooling all summer, heating the few weeks a year we actually need it. With a cold front heading into Tampa Bay this week, a lot of Riverview homeowners are about to flip the thermostat to HEAT for the first time since last winter. The most common call we get that first chilly morning? “It’s running, but it’s blowing cold air.”
Sometimes that’s normal. Sometimes it’s a real problem. Here’s how to tell the difference, what you can safely check yourself, and when to call a licensed tech from Nolan Air. You can see everything we cover locally on our Riverview HVAC service page.
First: heat pump “warm” feels cooler than you expect
A heat pump doesn’t blast hot air like a gas furnace. On a mild 50-degree morning, the air at the vent is usually somewhere in the mid-80s to 90s. Put your hand up to it and it can feel lukewarm, especially compared to your body temperature. If the house is slowly warming up and the vent air is clearly warmer than the room, your system is probably doing its job.
If the air coming out is the same temperature as the room, or colder, keep reading.
Check 1: Is the thermostat really on HEAT?
It sounds too simple, but we see it every cold front. Make sure the mode is set to HEAT (not COOL or AUTO with a low cooling setpoint), the fan is on AUTO rather than ON, and the setpoint is a few degrees above the current room temperature. If the screen is blank or dim, replace the batteries. Smart thermostats sometimes revert to a schedule after an update, so check that too.
Check 2: Is the outdoor unit running?
Walk outside. In heat mode, the outdoor fan should be spinning and you should hear the compressor humming. If the indoor blower is running but the outdoor unit is silent, the house will get room-temperature air at best. Look for:
- A tripped breaker in the panel for the outdoor unit or the air handler. Reset it once. If it trips again, leave it off and call us.
- The disconnect switch next to the outdoor unit pulled or switched off, which happens after yard work, pressure washing, or a pest service.
- Leaves, mulch, or overgrown landscaping packed around the coil. Give it at least two feet of clearance.
Check 3: Is it just in defrost?
On damp, chilly mornings, a heat pump will periodically run a defrost cycle to clear frost off the outdoor coil. During defrost it briefly switches modes, the outdoor fan stops, you may see steam rising off the unit, and the indoor air can feel cool for a few minutes. Your heat strips should kick in to cover it. That’s normal. If the cold air lasts much longer than 10 to 15 minutes, or the outdoor coil stays frosted over or iced up, something’s off.
Check 4: Swap the filter
A clogged filter chokes airflow, which makes a heat pump run inefficiently and can make heat strips overheat and shut off on their high-limit switch. Riverview’s newer homes still collect plenty of dust from ongoing construction around Big Bend and US-301. Put in a fresh filter before the front arrives.
When it’s time to call a tech
If you’ve checked all of the above and the vent air is still cold, it’s usually one of these:
- A stuck reversing valve. This is the part that switches your heat pump between cooling and heating. If it sticks, the system keeps cooling no matter what the thermostat says.
- Low refrigerant. A leak that you never noticed in summer shows up fast in heat mode, because the system has less margin when it’s cold outside.
- Failed heat strips or a bad sequencer. The backup heat that should cover defrost and colder nights isn’t coming on.
- A bad defrost control or sensor. The unit ices up and never clears.
- A failed capacitor or contactor keeping the outdoor unit from starting.
Those all need a licensed tech with gauges and a meter, not a YouTube video. Our heat pump repair in Riverview covers no-heat calls, reversing valves, defrost problems, and refrigerant leaks. If your system has strips or a furnace that needs attention, see our heating repair and tune-ups in Riverview.
Test it now, not on the coldest night
The best move is simple: switch to HEAT today, bump the setpoint up a few degrees, and let it run 15 minutes. If you get warm air and no strange smells, you’re in good shape. If not, call before the front arrives. Every cold snap, the schedule fills up the morning after the first chilly night, and nobody wants to wait on a repair while the house sits in the 50s.
Serving Riverview and nearby
Our techs work across south and east Hillsborough every week, including Ruskin, Plant City, and Seminole Heights. Same licensed techs, same straight answers.
Get your heat pump checked before the cold front. Call Nolan Air at (727) 353-9293, Monday through Friday, 8am to 7pm, or schedule online any time at NolanAir.com.